No Screws Through the Panel: 27 Squares of Old Town Grey Standing Seam in Lake City

September 2026 | Location: Lake City, FL (Columbia County) | Completed by: Hunter Lipthrott, J&M Roofing’s St. Augustine Branch

Most of the metal roofs on North Florida houses are held down by screws driven straight through the face of the panel — hundreds of them, each sealed by a rubber washer with a finite lifespan. Tracie’s new roof does not have a single one. On September 22, 2026, Hunter Lipthrott and the J&M Roofing St. Augustine crew installed 27 squares of 26-gauge Old Town Grey standing seam metal on her Lake City home, a system whose fasteners are hidden under the seams and whose panels are free to move with the temperature.

Project Details at a Glance

Location: Lake City, FL — Columbia County (32055)
Installation Date: September 22, 2026
J&M Roofing Specialist: Hunter Lipthrott — St. Augustine Branch
Property Type: Single-story country home with vinyl lap siding and masonry chimney
Roof Style: Hip with intersecting gables and a covered porch roof
Roof Pitch: 6/12
Roof Size: 27 squares
Product: 26-gauge standing seam metal roofing
Color: Old Town Grey
Scope: Full reroof — existing covering removed, new standing seam system installed
Permitting: Columbia County permit pulled and closed with final inspection

26-gauge Old Town Grey standing seam metal roof on a country home in Lake City FL by Hunter Lipthrott of J&M Roofing, September 2026

Standing Seam vs. Exposed Fastener: the Difference Is Where the Screws Go

“Metal roof” covers two systems that behave very differently, and the distinction is worth understanding before anyone signs a contract.

An exposed-fastener panel is screwed through its face into the structure below. It is the ribbed metal you see on barns, outbuildings, and a great many houses, and it is the more affordable of the two. It works, and it works for a long time. But every screw is a hole through the roof surface, sealed by a neoprene washer, and those washers are the system’s clock. Sun and heat harden them, thermal movement works the screws against their holes, and eventually they need attention — a maintenance item measured in years, not decades.

A standing seam panel is fastened differently. Concealed clips hold the panel down, hidden beneath the raised seams that join one panel to the next. From above, the finished roof has no exposed fasteners in the field at all. That removes the washer-aging problem entirely, because there are no washers in the water-carrying surface to age.

The second advantage matters just as much in Florida and gets discussed far less. Metal expands and contracts with every temperature swing, and a panel screwed rigidly through its face has nowhere to put that movement — so it works against its own fasteners, cycle after cycle, year after year. Standing seam clips are designed to let the panel slide as it expands and contracts. The roof moves the way metal wants to move, instead of fighting itself.

The trade-off is honest: standing seam costs more up front, and it demands more of the installer. The panels must be set true from the first run, because every seam after it follows. There is less margin for a crew improvising as they go.

Lake City and the Columbia County Oaks

Lake City sits where I-75 and I-10 cross in Columbia County, the North Florida crossroads that earned the town its “Gateway to Florida” nickname, in spring country between the Suwannee and Santa Fe rivers. Outside the city grid, the properties open up: wide lawns, long views, detached outbuildings, and the enormous live oaks that define this part of the state.

Tracie’s lot is exactly that. The photos show mature oaks with Spanish moss arching over the roofline from several directions, a brick paver walk curving around the house, a gazebo at the edge of the yard, and open grass running to a tree line. It is a beautiful setting, and it is a demanding one for a roof.

Oaks shed constantly here — leaves, acorns, twigs, and the moss itself — and anything that lands on an asphalt roof tends to stay there, holding moisture against a granular surface in a climate that is humid most of the year. That combination is what drives the algae streaking and premature aging common on shaded North Florida roofs. A smooth metal panel gives debris nothing to catch on. What lands on this roof slides off it, and what little remains dries fast.

The other factor is wind. Columbia County sits far enough inland that people sometimes assume tropical systems arrive spent, which is not how it works — storms tracking up the peninsula or in from the Gulf still carry real wind this far north, and a property with open ground around it has nothing breaking it up. A standing seam system with concealed clips and no exposed fasteners is a sound answer to that exposure.

Old Town Grey at a 6/12 Pitch

A Weathered Grey That Suits a Country House

Old Town Grey is a soft, slightly weathered grey — not the bright silver of a bare mill finish and not a hard charcoal. Against Tracie’s khaki-tan vinyl siding and white trim, it reads as a natural, settled roof color rather than a statement, which is right for a house in this setting. The warm siding keeps the grey from going cold, the white trim and gutters stay crisp beneath it, and the whole elevation sits comfortably under the oaks instead of competing with them.

Colored standing seam also carries a practical advantage over bare metal: a factory-applied finish holds its appearance far longer than an uncoated panel, and lighter and mid-tone greys reflect meaningfully more solar energy than dark colors. On a single-story home where the living space sits directly beneath the roof deck, that reflectivity is felt indoors on an August afternoon.

Why 6/12 Is a Good Pitch for This System

Six-in-twelve is steeper than most metal roofs in this part of Florida, and it works in the system’s favor in two ways. Water and debris leave quickly, so nothing sits long enough to matter — particularly useful under this much tree cover. And the roof is genuinely visible from the ground, which means the quality of the panel runs and the hip detailing is on display rather than hidden.

The geometry asks something of the crew in return. This is a hip roof with intersecting gables and a separate covered porch roof, so panels terminate into hip lines on several planes and the porch roof has to tie in cleanly to the main body. Standing seam is at its easiest on a simple rectangle. Every hip and every tie-in is a place where panels must be cut to angle and the seam detail carried through properly, and on a steep pitch all of it is visible from the yard.

Hunter Lipthrott on a Standing Seam Install

Hunter Lipthrott brings eight-plus years of residential roofing experience and holds GAF, CertainTeed, IKO, and NRCA ProCertification credentials. The NRCA credential is the one that counts most on this kind of project, because it is earned by demonstrating installation technique rather than by completing coursework — and standing seam is a technique-driven system.

There is very little a standing seam roof lets you hide. The panels run long and straight, the seams are the dominant visual line on the roof, and a run that starts out of square stays out of square all the way to the far hip. Getting it right means setting the layout carefully before the first panel goes down and holding that line across every plane. Homeowners across Columbia County who want that done properly can reach our team of North Florida roofers directly.

The Result

From the yard, the roof reads as a clean grey plane with evenly spaced seams running straight from ridge to eave, the hips meeting tight, and the porch roof tied in without a break in the rhythm. The chimney passes through cleanly and the panel field carries uninterrupted around it. There are no fastener heads anywhere in the visible surface — just the seams, which is the whole point of the system.

Tracie now has a metal roofing system with no exposed fasteners to age out, panels free to move with every temperature swing, and a smooth surface that sheds everything her oaks drop on it, permitted and closed with a Columbia County inspection. On a country property shaded by trees older than the house, that is a roof built for where it actually sits.

Project Specifications Summary

Product: 26-gauge standing seam metal roofing
Color: Old Town Grey
Roof Size: 27 squares
Roof Pitch: 6/12
Roof Style: Hip with intersecting gables and a covered porch roof
Fastening: Concealed clips beneath the seams — no exposed fasteners in the panel field
Scope: Full reroof — existing covering removed, new standing seam system installed
Property Type: Single-story country home with vinyl lap siding and masonry chimney
Exterior: Khaki-tan lap siding, white trim and gutters, brick paver walkway
Site Conditions: Mature live oaks with Spanish moss over the roofline, open rural lot
Permitting: Columbia County permit, closed with final inspection
Location: Lake City, FL — Columbia County (32055)
Specialist: Hunter Lipthrott — J&M Roofing St. Augustine Branch
Installation Date: September 22, 2026
Branch: St. Augustine — (904) 320-1968

27-square standing seam metal roof with concealed fasteners under live oaks in Lake City FL, Columbia County

Pricing Metal in Columbia County? Ask Which Kind You're Being Quoted

Two metal quotes can differ substantially and both be legitimate — one may be an exposed-fastener panel and the other standing seam, and they are not the same roof. Before you compare numbers in Lake City, Fort White, Live Oak, or anywhere in Columbia County, find out which system each quote describes, where the fasteners go, and how the panels handle thermal movement. We will walk you through both honestly, including when the less expensive system is the sensible choice for your house.

Call our St. Augustine office at (904) 320-1968, Monday through Friday, 9am to 5pm, for a free estimate and roof inspection.

Contact Us Today

Name(Required)
Location(Required)